Just hold the cup over it! Mondahmine Mouthwash Automatic Dispenser.

• Just hold the cup over it and one dose of Mondahmin will automatically come out, making it easy to use without any hassle.
• It can be used hygienically because there is no liquid dripping or stickiness from the bottle.
• A compact appliance that can be placed neatly in the washbasin.
• You can adjust the amount of discharge for one time to 2 stages of 10mL and 20mL (twice at a time of 10mL each).
• Life waterproof (IPX4)
  It can also be used around water such as a washstand.
  

  *It is not completely waterproof.

* Mondahmin bottle sold separately.

Play how-to video

Please read it carefully before use and use it correctly.

< Mondahmin can you use?>

• Mondahmin Peppermint
• Mondahmin Sensitive
• Mondahmin Strong Mint
• Mondahmin Premium Care Series
• Mondahmin NEXT Periodontal Care Series
• Other Mondahmin (excluding Mondahmin Whitening and NEXT Gum Care Series)

<Available sizes>

• 380 mL
• 700 mL
• 1080 mL
• 1300mL

*Some Limited Edition can be used in sizes other than those listed above.

Please be sure to check.
Cannot be used with the following Mondahmin:

• Sizes under 380mL, sizes 600mL, 1000mL, 3000mL

  I can't use it because the special cap doesn't fit the bottle.

• Mondahmin Whitening

  (Because the abrasive is mixed, the instrument body may be broken.)

• Mondahmin NEXT gum care series

  (Active ingredient may cause the cap to discolor.)

[How to use automatic dispenser]

• Open the battery cover on the bottom of the main unit while pressing the knob.
• Pay attention to the + and - direction, set AA alkaline batteries, and set the battery cover again.
• Open the cap of Mondahmin bottle, replace it with the dedicated cap, and tighten it tightly.
  *The tip of the tube will be above the liquid surface, but you can still use it without any problems. (Please do not cut the tube.)
• Set the bottle in the instrument body and push it firmly until it clicks.
  *The direction of the bottle can be either front or back.
• Place the main body of the device where you will use it, and switch the switch to "20 mL".
  * You can also set it to "10 mL" according to your preference.
  *When the switch is switched (OFF→10mL→20mL), the red operation check lamp blinks 6 times. When you start using it, please hold the cup over after the blinking is over.
• Hold the cup under the nozzle to dispense one dose (two 10 mL portions for the 20 mL setting). Put it in your mouth and rinse for 20-30 seconds before spitting it out.
  *When set to 20 mL: 10 mL each comes out in two batches. Hold your hand until the operation is finished.
  ・The mouthwash does not come out the first time you use it. Hold the cup over several times until the mouthwash comes out.
  ・When using continuously, remove the cup from the sensor once and hold it over again.
  ・If you hold the cup below or away from the operation confirmation lamp, the mouthwash may not come out.
  ・Since the sensor cannot detect transparent or translucent cups such as glass, it cannot be used.

[How to replace Mondahmin bottle]

• removing the bottle
  ・After confirming that the mouthwash does not come out from the nozzle, turn the switch of the device to "OFF" and pull the bottle straight up to remove it.
  *Do not throw away the dedicated cap. If you throw it away, you will not be able to use the equipment.
  * If you remove the bottle with the liquid remaining in the bottle, the liquid may leak into the bottle insertion part of the device. In that case, please wipe it off.
• Installing a new bottle
  Attach the special cap to the new bottle and use it correctly according to steps 4 to 6 of the instructions.
  *Please be sure to replace it with one of the usable Mondahmin listed under "Be sure to check" in the instruction manual.
  *If you are switching to a different product or are concerned about dirt inside the device, please refer to the "How to clean the automatic dispenser (device body)" in the "Instructions for Use" included with the product and clean the inside of the device.

[How to clean the automatic dispenser (equipment body)]
1.External device

・If the outside of the device becomes dirty, turn it to "OFF", wipe it with a soft cloth moistened with water, and dry it thoroughly.

・Wipe off any dirt on the nozzle or near the operation confirmation lamp. It may cause sensor malfunction.

The insert part of the bottle is easy to get dirty, so please wipe it off when replacing the bottle.

2. Inside the device

• Turn the switch to "OFF", fill an empty bottle with water (100 mL: about half a cup), attach the special cap, and push it firmly into the device until it clicks.

  * If mouthwash is attached to the tube of the special cap, please rinse it lightly with water before attaching it.

• Repeatedly pour out the water according to usage 5-6 to wash the inside of the device. (until the water in the bottle runs out)
• Remove the bottle by pulling it straight up and set the switch to 20mL. Since water remains inside the device, hold the cup over several times until no more water comes out of the nozzle.

  * The red operation confirmation lamp flashes 6 times. When you remove the water, hold the cup over after the blinking is over.

Even after cleaning, some water may remain inside the instrument, so please discard the first amount of liquid (two times for 10 mL setting) that comes out when you first use the new bottle.

[How to replace the battery]

When the battery level is low, the red operation confirmation lamp will continue to blink. (The mouthwash will not come out even if you put the glass under the nozzle.)
In that case, please replace with four new AA alkaline batteries. When replacing the battery may not work if you mix and use the manufacturer and old and new.

[Is it broken? If you think]
1. If the power does not turn on

・Check that the batteries are set in the correct orientation. If you set it in the correct direction and set the switch to "10mL" or "20mL", the operation confirmation lamp will blink 6 times.

2. When mouthwash does not come out

・Hold the cup within the sensing range of the sensor (between the nozzle and the operation confirmation lamp).
(The sensor will not detect if you hold the cup below the lamp or at a distance.)
・Turn the switch to "OFF" and wipe off the dirt after referring to "1. Exterior of the device" of "How to clean the automatic dispenser (device body)".
・Please use anything other than transparent or translucent cups such as glass. (The sensor cannot sense it.)
・Please use in a place where it is not directly exposed to sunlight or bright lighting. (The sensor cannot sense it.)

3. When the mouthwash comes out without holding the cup up

・Since there is a possibility that dirt is attached around the sensor and operation confirmation lamp, turn the switch to "OFF" and refer to "Cleaning the automatic dispenser (equipment body) 1. Exterior of the equipment". Please wipe off the dirt.

If the above does not resolve the issue, please contact Earth Corporation 's Customer Support Center.

• Please do not use for any purpose.
• Do not disassemble the automatic dispenser (device body).
• Not completely waterproof. Do not immerse in water or expose to running water.
• I can not wash it.
• Do not place in places subject to high temperature and humidity, or on unstable surfaces such as tilted places.
• Transparent and translucent glass such as glass can not be used because the sensor can not detect it.
• You can use Mondahmin series of cosmetics and Quasi-drug (excluding Mondahmin Whitening, Mondahmin NEXT gum care series, and Mondahmin concentrated type). To avoid damage to the device itself, do not use any products other than Mondahmin.
• When lifting, please turn the switch to "OFF". When the switch is set to "10mL" or "20mL", if you lift the main body of the device or touch the area around the sensor, the sensor may detect it and the mouthwash may come out.
• When cleaning the wash basin etc. which installed the instrument body, please set the switch to "OFF" to prevent the rinse liquid coming out by mistake.
• Keep out of direct sunlight and out of reach of children.
• If you do not use it for a long time, some of the ingredients in the mouthwash may harden near the nozzle. In that case, wipe it off with a soft cloth dampened with water.
• Do not use chlorine-based detergents or abrasives nearby as this may cause discoloration of the instrument body.
• The standard use period of the instrument body is about 3 years. However, depending on the operating environment, the period may slightly go back and forth.

This product falls under the category of aviation dangerous goods under the Civil Aeronautics Act.

When requesting shipping from a carrier (post office, etc.), please inform them in advance that this product is classified as "Dangerous Goods by Air" and confirm that they are able to ship it.

View All

See the instructions enclosed with the product(PDF: 2,188KB)